1. Intermediate current

The intermediate current refers to the current value of the coaxial cable of the power filter and the end of the axis to the ground. Usually, a machine is used for conducting current meter inspection.

2. Large leakage voltage

Leakage voltage refers to the significant amount of voltage (usually measured at 250vac/50Hz) that the coaxial cable of the power filter, axis to ground (shell), can withstand when obtaining the operating frequency and frequency. To ensure reliability, there are different requirements for different types and uses of power filters in entertainment venues. Usually, customers do not have equipment to measure the leakage voltage of PR320, and the overall power filter calibration value should be adjusted in all aspects.

3. Environmental temperature

The usual Mohr number is: δ 30 ℃.

4. MC966CH

MC966CH considers the overall Mohr number of power filters and power filters, usually expressed in the form of sound and alcohol or unit sine positive response charts. It refers to the power filter connected to the railway line side by side, and the circuit design sends the power ratio or network address working frequency ratio to the loss. Il=10igpo/p2 (db) il=20igvo/v2 (db) spo, p2, vo, and v2 respectively express the power loss and operating frequency of the web end when the power filters are connected side by side.

5. Negative impact forms

To control the bottlenecks related to the negative impact of data transmission, it is also necessary to control the two forms of data transmission signals: co LiVernon and differential LiVernon. Raipur negative impact (also known as spin negative impact) refers to the detonation in the application software coaxial cable, where Raipur voltage escapes from two coaxial cables and drains from the other two coaxial cables, which is incompatible with the contact point. PSRR obstruction (also known as less negative impact) causes a working frequency at each coaxial cable, axis, and ground end, and the voltage of PSRR flows from Li Daoyan to the ground wire and back to the coaxial cable from the contact point.

6. Samud category

According to part of diniec68, the Samud category consists of three numbers.

For example, 40/85/21, where

40 expressed stability intensity -25 ℃.

85 expression stability limit+85 ℃.

21 expressed in water vapor relative humidity of 90-95% can exceed 21 days.

7. Ohmic connection

On both sides of the power filter, the ohm of the right side is 50 ω Describe the characteristics of the power filter under the device, as it is convenient and fast for inspection and complies with frequency normalization. But in the specific utilization, zs and zl are very complex, and the frequency points to be Mouy will be unknown.

1. Containment gain

The MLAD-V-SR inverter exclusive output power filter and MLAD-S-SR converter exclusive output power filter are all components of the switching power filter, which are specifically designed for inverters, converters, and other specialized power filters. In essence, they are also switching power filters. This power filter is mainly used to suppress low-frequency gain of 10KHz-30MHz.

2. Increase control system low-frequency

Even if the MLAD-V-SR inverter exclusive output power filter and MLAD-S-SR inverter exclusive output power filter contain resistors, they can provide more intuitive apparent power required by the control system on site, thus having a great promoting effect on improving the apparent power of the control system.

3. Provide more reliability, flexibility, and reliability of control systems

After installing switch power filters such as MLAD-V-SR inverter exclusive output power filter and MLAD-S-SR converter exclusive output power filter, it can effectively solve problems such as false alarms, overloads, and rejection caused by switch gain. The reliability, flexibility, and reliability of the control system have been significantly improved.

4. Resolve gain barriers and challenges

Difficulties such as misreporting, overload, and refusal to move are usually caused by gain, in addition to other reasons such as the product/device. Installing a dedicated output power filter for MLAD-S-S-SR converters and an dedicated output power filter for MLAD-V-SR inverters has a ≥ 95% chance of successfully solving such problems.

5. Qualified quality of on-board thermal energy products

National standards such as GB/T 14549 and EN51000 have standardized the quality of thermal energy products. However, with the use of linear electronic devices, it is often difficult to perform gain sampling for single compartment upgrades. Installation of MLAD-S-SR converter exclusive output power filter, MLAD-V-SR inverter exclusive output power filter, MLAD-GFC series product LCL gain power filter, MLAD-MFCA76RE furnace exclusive power filter Switching power filters such as MLAD-APF passive gain power filters can suppress gain and assist in restoring the quality of thermal products in the control system to within the national standard range.